Topic: problem sa ESC i motorom (Read 3430 times) previous topic - next topic

kupio sam nedavno komplet zagija od profesionalca iz Ivanića, međutim tu su neki problemi nastali, nemogu ga startat nikako,  baterija 2200, 40A regler, i motor 2200, prop 7,5 u čemu je kvaka? bacim ga dodajem gas on zablokira, malo ili više gasa sasvim svejedno zablokira i sve se grije, molim pomoć

Pa sto kaze profesionalac iz Ivanića?

kaže da je to normalno

imam osjećaj da tu nešto opasno ne štima i da me oštetio najmanje za 300kn, neznam kaj da radim, fakat mi je dosta

može slike zagija?

Ako ti motorić krene  pa zaškripi i stane, krivi ti je "Timing Setup". Probaj u postavkama ESCa
narediti na "Automatic" pa isprobaj kako se ponaša motorić, na zemlji naravno. Nevredi ti
bacati avion u zrak ako motorić neradi kako treba!

1. da li je baterija napunjena?

2. Djdarky ima pravo, mogao bi biti 'timing', iako nije loše i podesiti 'soft-start' na ESC-u.
3. grijanje....elisa 7*5 za taj setup bi prije išla 6*4...
...
Damir

a kak da to nariktam? nemam programing card a imam flysky tx

kak da slike stavim tu???

Koji imaš ESC (regler)?

evo pogledaj na slici, "majstor" kaže da je 40A i da to mora letit bez brige

Ja ga po izgledu neprepoznajem, šta piše gore na njemu?

1. Koji ESC koristiš, za početak?
2. Tema nema veze sa zagijem
3. Koliko mi je poznato ovdije se nitko profesionalno ne bavi modelarstvom ( ili se varam )
4. http://www.flyfreak.net/general-discussion/predstavite-se/840/

 

1,H40A ESC Brushless Motor Speed Controller 2,BEC output 2A 3,Battery Li-ion/Li-poly 2-3s 4good performance 5,fast delivery
H40A ESC Brushless Motor Speed Controller specially for rc helicoptors
Type :40A
Cont.Current : 40A
Burst Current :50A
BEC Mode : Linear
BEC output : 2A
Battery Li-ion/Li-poly :2-3s
Cell NIMH/NICD: 5-10
Throttle Range Setting Function
throttle range retting (Throttle range should be reset whenever a new transmitter is being used)
Program the ESC with your transmitter
1, Enter program mode
a, Swith on transmitter ;move throttle stick to top,connect the battery pack to ESC
b, Wait for 2 seconds , move should emit special tone like "beep-beep-
c, Wait for antoher 5 seconds,special tone like BSLCDL should be eimtted ,which means program mode is entered
Programmable items:
1,Barke Setting :Enabled /disabled,default  is disabled
2,Battery type: LI-XX (Li-ion or Li-poly ) /Ni-XX ( NIMH or NICD) .default is LI-XX
3,Low voltage Protection Mode( cut-off mode ) : Soft Cut-off (Gradually reduce the output power ) or Cut-off ( Immediately stop the output power ) .Default is Soft cut-off .
4, Low voltage  Protection Threshold (cut-off  Threshould ) :Low /Medium /High ,default is Medium
1) For lithium batteries , the number of battery cells is calculated automatically .Low /medium /high cutoff  voltage for each cell is 2.6V/2.85V/3.1V.
2) For nickel batteries , low/medium /high cutoff voltage is 0%/45%/60% of the startup voltage
5, Startup mode: Normal /soft /super -soft .default is normal
6,Timing :Low /Medium /High .Default is low .Note 2
Uaually ,low timing value can be used for most motors .We recommend the Low timing vlue for 2 poles motor and medium timing value for motors with more than 6 poles to get a high efficiency .For higher speed ,High timing value can be chosen.
Note 2 : After changing the timing setting ,Pls test your RC model on ground prior to flight .




Također treba provjeriti da li je motor OK, tj. da li su svi magneti fiksirani ( zaljepljeni ).

 

Ovaj ESC se ( osim direktno sa stanicom )  može programirati Turnigy ili Hobbiwing karticama.