Skip to main content

Topic: Racing quad - Team Hrvatska (Read 1086924 times) previous topic - next topic

0 Members and 5 Guests are viewing this topic.

Odg: Racing quad - Team Hrvatska

Reply #2940 –
Evo i testa materjala na malo vecem istom quadu (duzi krakovi)


http://www.youtube.com/watch?v=rHAknbRfIsI


http://www.youtube.com/watch?v=UMUFB1HPbW0
Futaba T14SG & T10CP / MXS EXP 64" / Xperience 132" / Spirit V2 80" / DLG Vortex 60" / NAN Nelly 72" / FPV Quad 500 & 290 &250 & 190 size / FS Dominator / MXS hybrid 49" / Hummer EPP 40"
https://sites.google.com/site/trenutakuvremenu / https://sites.google.com/site/deepskyhunters
 

Odg: Racing quad - Team Hrvatska

Reply #2941 –
To nije test materijala nego krutosti pojedinog oblika/konstrukcije. Materijal ima mehnicka svojstva koja ima.

Odg: Racing quad - Team Hrvatska

Reply #2942 –
Quote from: Tommee on
To nije test materijala nego krutosti pojedinog oblika/konstrukcije. Materijal ima mehnicka svojstva koja ima.


Onda to!
Hvala
Futaba T14SG & T10CP / MXS EXP 64" / Xperience 132" / Spirit V2 80" / DLG Vortex 60" / NAN Nelly 72" / FPV Quad 500 & 290 &250 & 190 size / FS Dominator / MXS hybrid 49" / Hummer EPP 40"
https://sites.google.com/site/trenutakuvremenu / https://sites.google.com/site/deepskyhunters

Odg: Racing quad - Team Hrvatska

Reply #2943 –
Jedva cekam test  :-X

Odg: Racing quad - Team Hrvatska

Reply #2944 –
Quote from: mibo on
Da li postoji mogučnost "armiranja" frejma, ruku,...prilikom printa?
Tipa: Printaš, postaviš armaturu, nastaviš printat po njoj?


Mi smo printali fuckaljku jednu ... sprintao na pola ... stisnuli pauzu ... "odljepili" lopticu unutara i nastavili printat ... tako da mozda
i imas tu mogucnost a i neznas ;)


ovu tu ja mislim :) --> http://www.thingiverse.com/thing:1046

Odg: Racing quad - Team Hrvatska

Reply #2945 –
Ah ti modelari.. Prije rovarili po balzi a sada po plastici  :D
Odlične ideje Stefano.
Kršite svoje koptere da biste ih bolje upoznali ! :-)
A sada i avione! :-(

Odg: Racing quad - Team Hrvatska

Reply #2946 –
Da vas nešto pitam,dali vam se isplati 3D printat dijelove ili se bolje isplati kupiti gotov frejm,i dali je 3D printani čvršči od ovih nazovimo ih "kupovnih"?

Odg: Racing quad - Team Hrvatska

Reply #2947 –
Bulldog, dobra slika profila :D
InnovationMatters

Odg: Racing quad - Team Hrvatska

Reply #2948 –
Ich seh den Wald vor lauter Baeumen nicht!!

Odg: Racing quad - Team Hrvatska

Reply #2949 –
:)
Ich seh den Wald vor lauter Baeumen nicht!!

Odg: Racing quad - Team Hrvatska

Reply #2950 –
Nije losa? :D

InnovationMatters

Odg: Racing quad - Team Hrvatska

Reply #2951 –
A ova
Ich seh den Wald vor lauter Baeumen nicht!!

Odg: Racing quad - Team Hrvatska

Reply #2952 –
Ich seh den Wald vor lauter Baeumen nicht!!

Odg: Racing quad - Team Hrvatska

Reply #2953 –
Ovo mi se pari da bi moglo bit dobro;)
Ich seh den Wald vor lauter Baeumen nicht!!

Odg: Racing quad - Team Hrvatska

Reply #2954 –
hm... najbolje probat :)
InnovationMatters